732 356 4438
Advanced Process TechnologyAdvanced Process Technology
  • HOME
  • ABOUT
    • Our History
  • CHOOSE A PROCESS
    • Open Casting
    • Closed-Mold Injection
    • Vacuum Casting
    • (RTM) Resin Transfer Molding
    • (VARTM) Vacuum-Assisted Resin Transfer Molding
    • RTM/VARTM Combo
    • Filament Winding – Resin Bath Filling
  • PRODUCTS
    • SRD Series
    • SRD i Series
    • ECS-Series
    • Flying Wedge
    • Tanks
    • Quick Ship Tanks
  • SUPPORT
  • CONTACT

Batch Tanks – for Heating, Agitating, and Vacuum Degassing

These tanks are used for mixing, heating and degassing batches of resin. They are also available without heat. One tank can be purchased for hand-batching or multiple tanks can be used for automatic machine processing. Quantities prepared this way can range from two-pounds to two-thousand pounds and more. Much larger quantities are continuously heated and degassed in our on-the-fly degassers.

Batch Tank – Benefits:

  • Peace-of-mind, you know the entire batch is ready before you pour.
  • Provides high-quality, air-bubble and void-free resin materials.
  • Maintains materials at precise preset temperature (+/- 1oF) to 285oF or more.
  • Available in 0.5, 2, 5, 10, 15, 30, 60, 75, 100 and 250-gallon tank sizes with many standard options to match your specific process requirements.
  • Independent temperature controls let you connect various sizes and types of portable APT tanks to your process equipment.
  • Rugged construction offers dependable operation.
Description/Operation:

You can manually pour a batch of resin into the tank’s fillport or draw it in via vacuum (i.e., the same vacuum you use for degassing) with an optional Resin Vacuum Transfer System.
Once the material is raised to the required elevated temperature and viscosity is lowered, vacuum breaks the air-bubbles and dissolved gasses. This can result in a violent bubbling action, which settles-down as most of the air is removed. The agitator’s pumping motion continues to bring fresh material to the resin’s surface for outgassing — up on the sidewall and down along the agitator shaft, which also helps to maintain homogenous temperature control and proper suspension of fillers throughout the batch. Once fully heated and outgassed, the material can be fed to your hand-casting station or to downstream automatic equipment. Gravity or dry nitrogen gas over-pressure (used to eliminate moisture contamination) can be used to drive material out of the tank. When constant vacuum is maintained on the material or when material recirculation (from the tank, to the metering pump, to the mixer and back to the tank) is required, internal or external feed pumps can be used to provide necessary positive output pressure to the machine. These tanks are available without heat and special APT tanks, with high- temperature control to 500oF, are available. Electric heat is standard. We also supply heated oil-jacketed tanks.

OLYMPUS DIGITAL CAMERAOLYMPUS DIGITAL CAMERA
Material Temperature and Vacuum Levels:

Resins typically require heating and agitation to significantly lower the resin’s viscosity and surface-tension — to remove all the air and dissolved gasses — prior to metering, mixing and dispensing into molds. Some low viscosity materials are easily outgassed without heat, however, consistent degassing with materials having a viscosity of 1,000 cps or higher often relies on precise (±1oF) temperature control of the materials. Consistent outgassing requires accurately controlled temperatures and vacuum levels.

To eliminate air-bubbles, no matter how air-free the materials might look coming out of the supply drums, vacuum must be drawn on the materials. The entire range of vacuum levels typically used to remove air from resin materials ranges from 5 millimeters vacuum to 0.05 millimeters (50 microns) from perfect vacuum. Degassing at levels between 5.0 mmHg and 2.0 mmHg makes low to medium viscosity urethane and epoxy resins visibly “air-free”. If you pot or encapsulate high voltage electrical or electronic components, 1.0 mmHg vacuum or less will be required and you will typically need to pour those parts inside a vacuum chamber. APT manufactures a wide variety of Vacuum Potting Systems, including mixing machines and vacuum chambers. If your materials include volatile components that will gas-off quickly or they just need need some slight vacuum (for example, 25 to 29 inches of mercury) to remove gross air, we offer timed vacuum sequences in place of constant vacuum.

Vacuum Levels Required for Degassing Resins:

30″ Vacuum = 0.0 mmHg (Torr) = 0.0 microns = Perfect Vacuum
0.05 mmHg (Torr) = 50 microns
0.1 mmHg (Torr) = 100 microns
0.5 mmHg (Torr) = 500 microns (Resin is degassed at 50 to 500 microns to vacuum pot and
encapsulate critical high voltage assemblies and epoxy composite components.)
1.0 mmHg (Torr) = 1,000 microns
2.0 mmHg (Torr) = 2,000 microns (Resins degassed at 500 to 2,000 microns are typical for
most vacuum potting and epoxy composite resin infusion applications.)
5.0 mmHg (Torr) = 5,000 microns (Resin is degassed down to 2 to 5 mmHg to pour and cast
visibly air-free cast urethanes and epoxies. 5 mmHg is five times better than 29″ of vacuum.)
10.0 mmHg (Torr) = 10,000 microns
29″ Vacuum = 25.4 mmHg (Torr) = 25,400 microns
28″ Vacuum = 50.8 mmHg (Torr) = 50,800 microns (Very low viscosity materials are degassed
at 10 to 50 mmHg vacuum.)
15″ Vacuum = 381 mmHg (Torr) = 381,000 microns
0″ Vacuum = 762 mmHg (Torr) = 762,000 microns = Ambient Air

  • SRD Series
  • SRD i Series
  • ECS-Series
  • Flying Wedge
  • Tanks
  • Quick Ship Tanks
View Diagram

AVAILABLE CUSTOMER SERVICE

We are committed to responsive after-sale service and technical support.

After delivery, we check the installation.

Assist with running your SRD, ECS or HT-Series system with your material.

Your designated machine-operators can be trained.

SITEMAP

  • HOME
  • CHOOSE YOUR RESIN PROCESS
  • PRODUCTS
  • SUPPORT
  • CONTACT

Contact Us

732.356.4438

732.356.4005

200 Egel Avenue
Middlesex, New Jersey 08846
© 2015 All rights reserved.